Many alignment problems can be fixed with basic tools and a careful approach. You don’t need to be an expert to make things better. Sometimes a simple adjustment gets the door working again, improves security, and helps you avoid a larger commercial door repair bill later.

Common Causes of a Misaligned Commercial Door Frame

Understanding why a commercial door frame becomes misaligned helps you fix the root cause. Here are the most common reasons this happens in shops, warehouses, and office buildings:

• Loose hinge screws: The constant weight of a heavy commercial door can loosen screws over time. When the screws back out even a little, the door sags, and the gap at the top and the latch side changes.
• Building settling: All buildings shift slowly as the ground beneath them compacts. This movement can pull a door frame out of square.
• Warped wood or metal: Changes in humidity or temperature can twist a wooden frame. Metal frames in unheated spaces can also expand and contract enough to throw off alignment.
• Foundation problems: Cracks in the floor or wall near the door opening often indicate that the foundation is moving. This directly affects the frame.
• Worn or bent hinges: High-traffic doors are slammed, kicked open, or propped with wedges. Bent hinges cause the door to hang at an angle, no matter how tight the screws are.
• Improper installation: If the frame was never installed level or plumb, it will only worsen with use.

Tools You May Need to Repair a Misaligned Commercial Door

Before you begin, gather a few basic tools. Having everything ready helps the job go smoothly.

• A sturdy screwdriver (flathead and Phillips) or a drill with driver bits
• A 4-foot level (or longer if you have one)
• Wood shims or plastic composite shims
• A hammer
• Replacement screws (3-inch construction screws often work better than short hinge screws)
• A utility knife (for cleaning out old paint or caulk around the frame)
• A pry bar (in case you need to gently shift the frame)

Also Read: Door Installation Tools Every Homeowner Needs

Steps to Fix a Misaligned Commercial Door Frame

The steps below cover the most common fixes. Try one or more, depending on what you find during your inspection. Work slowly and check your progress after each adjustment.

1. Inspect the Hinges and Screws First

Open the door fully and inspect each hinge leaf. Wiggle the door up and down. If you see the hinge leaves rubbing against the frame or the door edge, the screws are loose. Mark any spot where the wood or metal around a screw hole looks crushed or stripped. 

On a metal frame, check whether a screw has rusted or snapped off. This inspection shows what needs tightening or replacing

1. Tighten or Replace Loose Screws

Using your screwdriver or drill, tighten each hinge screw slowly. Do not overtighten, as that can strip the hole. If a screw keeps spinning and never grabs, the hole is worn out. Remove that screw and replace it with a longer one. A 3-inch construction screw can reach past the frame and bite into the stud behind it. That often pulls the entire hinge side of the frame back into place. 

If the frame is metal, you may need a self-tapping screw of the same size. After tightening, close the door and check the gap between the door and the frame on all sides. A more even gap indicates the fix is working.

1. Check the Frame for Gaps and Add Shims

Place your level against the hinge side and the top of the frame. If the frame isn’t straight, you’ll need to add shims. Check behind the trim or weatherstripping for gaps between the frame and the wall. Slide a thin wood shim into any gap larger than one-eighth of an inch. Tap it in gently with a hammer, then check the level again. Don’t try to move the frame too much at once. Add shims in pairs on both sides of a gap to keep the pressure even. 

Many commercial door repairs involve re-shimming frames that have shifted over time. Once the frame is level and straight, secure the shims with a finish nail or a screw to keep them in place.

1. Adjust the Strike Plate

When the door aligns well but still will not latch, the problem is usually the strike plate. Look at the mark where the latch bolt hits the metal plate. If the bolt is hitting too high, too low, or just catching the edge, move the strike plate slightly. Remove the plate and use a metal file to widen the opening in the direction the bolt needs to go. Sometimes moving it by one-sixteenth of an inch is enough. 

You can also fill the old screw holes with a wooden toothpick or a small piece of a shim, snap it off flush, and drill new pilot holes in the corrected spot. Reattach the plate and test the latch. The bolt should slide in smoothly without pushing the door up or down.

1. Test the Door and Make Small Tweaks

Open and close the door several times at normal speed. Watch the gap along the top and the latch side. Listen for rubbing. If the door still drags slightly on the floor, a thin shim behind the bottom hinge can lift that corner a bit. If the top corner is sticking against the frame on the latch side, a shim behind the top hinge or a slight bend in the hinge knuckle might help. 

After you are satisfied with the swing, tighten all hardware one final time. Good alignment means the door stays where you leave it when opened halfway, and the latch clicks easily without having to lift or push down on the handle.

When a Simple Fix is Not Enough

Some misalignment problems go deeper than loose screws or missing shims. If you notice any of these signs, the door frame likely needs professional attention.

• The frame is visibly bent or cracked
• Large cracks run through the surrounding wall
• The floor has sunk or heaved near the opening
• The door binds even after shimming and adjusting all hinges
• The metal frame has pulled away from the wall more than a quarter inch

In these situations, forcing the door to work can damage both the frame and the door. Professional commercial door repair in Rochester can address structural issues that cause misalignment. A technician can check if the opening has shifted, weld a cracked frame, or replace damaged anchor points so the door works properly.

Also Read: How to Choose a Commercial Door Repair Company

Let Rochester Door Company Handle it!

When a misaligned door frame needs more than a quick DIY fix, the Rochester Door Company team is ready to help. We’ve repaired many commercial entrances in the area, from retail stores to warehouse bay doors. Our repair process examines everything, including the frame, hinges, wall structure, and door closer. We restore the opening to factory-level alignment and make sure it stays that way.

For reliable commercial door repair in Rochester, you can count on our experienced technicians. We use strong hardware and proven shimming methods that withstand daily business use. Your safety and your building’s security are important to us, so we arrive on time, explain the work clearly, and make sure your door works smoothly.

The post How to Fix a Misaligned Commercial Door Frame appeared first on Rochester Door Company.

In this blog, we’ll explain the key differences between fire-rated doors and regular doors. You’ll learn what makes a door fire-rated, why it matters, and where these doors are required. This information can help you make safer choices for your home, office, or any building.

What Is a Fire-Rated Door?

A fire-rated door is built to stop fire from spreading for a certain amount of time. It resists catching fire and blocks smoke and heat. These doors are tested in labs to see how long they can hold back a fire, usually measured in minutes. Common ratings are 20, 45, 60, and 90 minutes.

Fire-rated doors are made from strong, noncombustible materials. The frame, hinges, and handles are also fire-rated. These parts work together to keep fire on one side of the door. This gives people more time to get out and helps firefighters do their job.

What Is a Regular Door?

Most homes and small offices have regular doors. They can be made from wood, hollow wood, metal, or glass. These doors are good for everyday use, giving privacy and blocking sound, but they aren’t made to stop fire.

Regular doors can catch fire and burn, and smoke can easily get through the sides or bottom. In a fire, a regular door can even make the flames worse. They don’t protect people or property, so they shouldn’t be used where fire safety matters.

Key Differences Between Fire-Rated Doors and Regular Doors

Here are the main differences between these two types of doors:

Materials Used

• Fire-rated doors are made of steel, gypsum, fire-resistant wood, or special cores such as mineral wool. These materials don’t burn quickly.
• Regular doors are made from standard wood, hollow wood, aluminum, or glass. These materials can burn or melt in a fire.

Also Read: Aluminum vs Wood Doors – Best Choice for Rochester NY

Time of Protection

• Fire-rated doors are tested to hold back fire for 20 to 90 minutes or more. You can find the rating on the door label.
• Regular doors don’t have a fire rating. They may fail in less than five minutes.

Smoke and Heat Seals

• Fire-rated doors have special seals around the edges. When heat touches these seals, they swell up and block smoke and hot gases.
• Regular doors don’t have these seals. Smoke can get under or around the door very quickly.

Hardware and Frames

• Fire-rated doors need special hinges, handles, and locks. These parts are tested for heat and fire, and the frame must be fire-rated too.
• Regular doors can use any standard hardware, and the frame isn’t made for fire safety.

Cost

• Fire-rated doors cost more because they use stronger materials and must pass safety tests. Installing them also takes more care.
• Regular doors cost less and are easier to buy and install.

Where They Can Be Used

• Many buildings in Rochester are required by law to have fire-rated doors. These include apartment buildings, offices, factories, schools, and hospitals. Homes also need them between the garage and the living area.
• Regular doors are used for bedrooms, bathrooms, closets, and other rooms that don’t need fire protection.

Why Fire-Rated Doors Are Important for Safety

Fire can spread fast. In less than three minutes, a small flame can become a big fire. Smoke is even more dangerous; most fire injuries are caused by smoke, not flames.  Fire-rated doors in Rochester slow down both fire and smoke.

Here’s an example. If a fire starts in a garage and the house door is a standard door, the fire can reach your home in minutes. But if that door is fire-rated for 20 minutes, you have time to wake up, get your family, and leave safely. Those extra minutes can make all the difference.

Fire-rated doors also help protect property by keeping fire in one room or area. This means less damage to the rest of the building and lower repair costs. Some insurance companies even offer lower rates for buildings with fire-rated doors.

Where You Need Fire-Rated Doors in Rochester

Rochester building codes follow national safety rules. These rules require fire-rated doors in certain places. Here are some examples.

• Between a house and an attached garage: Most local codes require a fire-rated door here. If your garage is connected to your home, check your door for a fire rating label.
• Stairwells in buildings with more than two floors: Stairs need fire-rated doors so people can escape without smoke blocking their way.
• Furnace rooms or mechanical rooms: These rooms have equipment that can start a fire. A fire-rated door keeps the fire from spreading.
• Kitchens in restaurants or commercial buildings: Many fires start in kitchens, so fire-rated doors are often required.
• Hallways in apartment buildings: Each apartment door is usually fire-rated. This protects neighbors if a fire starts inside one unit.
• Storage rooms with flammable items: Paint, gas, cleaning supplies, and paper can catch fire quickly. A fire-rated door slows the spread.

If you live or work in Rochester, take a look at your doors. Ask yourself if a room needs fire protection. If it does, you may need a fire-rated door. Don’t guess; check with a local expert or building inspector.

How to Tell If a Door Is Fire-Rated

Many people don’t know if their door is fire-rated. It’s easy to check. Look for a small label on the edge of the door, usually on the hinge side or top edge. The label will say something like “20-minute fire rating” or “45 minutes.” It may also show a number like “20/45/60/90.” The label comes from a testing group. Never paint over or remove this label. If the label is missing, you can’t be sure the door is still fire-rated.

If you don’t see a label, the door is probably a regular door. Some older doors may have lost their label, so it’s best to ask a professional to check. Don’t assume a heavy door is fire-rated, some regular doors are heavy too. Always check for the label.

How Rochester Door Company Can Help

At Rochester Door Company, we’ve helped many homeowners and business owners choose the right doors for safety and everyday use. Our team understands local building codes and fire safety regulations. We use only tested products that meet all safety standards.

If you need fire-rated doors or want to learn more about fireproof doors in Rochester, we’re here to help. You can ask us about your current doors, and we’ll check whether they’re safe. We can also help you choose new doors that match your needs and budget.

The post Fire-Rated Doors vs Regular Doors: What You Need to Know appeared first on Rochester Door Company.

If you live in or manage a property, understanding apartment door repair in Rochester helps you stay prepared. This guide explains everything in simple and clear language so both tenants and landlords can handle door issues the right way. 

Why Apartment Door Repair Matters More Than You Think 

Many people ignore small door problems at first. A slight noise or a loose handle may not seem serious. Over time, these small issues turn into bigger and more expensive problems. 

A damaged door can affect security. It can also increase energy costs if there are gaps allowing air to pass through. For landlords, it can lead to tenant complaints. For tenants, it can reduce comfort and peace of mind. 

That is why apartment door repair in Rochester should always be handled on time. Taking action early saves money and avoids unnecessary stress. 

Most Common Apartment Door Problems 

Apartment doors go through daily use. Because of this, they often develop certain common issues. 

Door Not Closing Properly 

This is one of the most common problems. The door may stick, drag on the floor, or fail to latch. This usually happens due to misalignment or loose hinges. 

Loose or Broken Handles 

Handles become loose after repeated use. In some cases, they may break completely. This makes it difficult to open or close the door. 

Lock Issues 

Locks can become hard to turn or stop working altogether. This is a serious issue because it affects safety. 

Gaps Around the Door 

Gaps allow air, dust, and noise to enter. This reduces comfort and increases energy bills. 

Damaged Door Frame 

A cracked or weak frame can make the entire door unstable. It also affects how the lock functions. 

All these issues make apartment door repair in Rochester a regular need for both tenants and landlords. 

Also read: Door Installation Tools Every Homeowner Needs 

What Causes These Problems 

Understanding the cause helps you prevent future issues. 

• Daily wear and tear from frequent use 

• Changes in the weather that affect wood and metal 

• Poor installation 

• Lack of maintenance 

• Accidental damage 

In a city like Rochester, seasonal changes can impact door materials. This makes regular inspection even more important. 

Responsibilities of Tenants and Landlords 

One of the biggest concerns is who should handle repairs. 

Tenant Responsibilities 

Tenants should take care of basic maintenance. This includes keeping the door clean and reporting issues as soon as they notice them. If damage happens due to misuse, tenants may need to pay for repairs. 

Landlord Responsibilities 

Landlords are responsible for major repairs. This includes fixing locks, replacing damaged frames, and ensuring the door is secure. They must provide a safe living environment. 

Clear communication between both sides helps avoid confusion. Reporting issues early makes apartment door repair in Rochester smoother and faster. 

Warning Signs You Should Not Ignore 

Some door issues need immediate attention. Ignoring them can lead to bigger damage. 

• The door does not lock properly 

• Cracks in the frame 

• The door feels loose or unstable 

• The handle is about to fall off 

• Air leaks through the edges 

If you notice these signs, it is time to act quickly and consider apartment door repair in Rochester. 

Easy Fixes You Can Try at Home 

Not every problem needs professional help. Some small fixes are simple and effective. 

• Tighten Loose Screws: Loose hinges can cause alignment issues. Tightening screws can solve the problem quickly. 

• Lubricate Hinges and Locks: Applying oil can reduce noise and improve movement. It also helps prevent further wear. 

• Adjust the Door Alignment: Sometimes, a small adjustment can make the door close properly again. 

• Replace Weather Seals: Adding new seals can stop air leaks and improve insulation. 

When You Should Call a Professional 

Some problems are too complex to fix on your own. Trying to repair them without proper tools can make things worse. 

You should call a professional if: 

• The door frame is damaged 

• The lock is completely broken 

• The door is heavily misaligned 

• Security is compromised 

Professional services for apartment door repair in Rochester ensure that everything is fixed correctly and safely. 

Cost of Apartment Door Repair in Rochester 

The cost of repair depends on the problem. 

• Minor fixes, like tightening or lubrication, are affordable 

• Lock repairs or replacements cost a moderate amount 

• Frame repairs or full door replacement cost more 

For tenants, reporting issues early can help avoid paying for bigger repairs later. For landlords, regular maintenance reduces long-term expenses. 

Safety Should Always Come First 

A door is your first line of defense. If it is not working properly, it can put your safety at risk. 

Make sure: 

• The lock works smoothly 

• The door closes completely 

• The frame is strong 

• There are no visible gaps 

If any of these conditions are not met, immediate apartment door repair in Rochester is necessary. 

Preventive Maintenance Tips 

Preventing problems is always easier than fixing them. 

• Inspect your door regularly 

• Clean hinges and locks 

• Avoid slamming the door 

• Check for early signs of damage 

These simple habits can extend the life of your door and reduce repair needs. 

Benefits of Timely Repairs for Landlords 

Landlords who handle repairs quickly enjoy several benefits. Tenants feel satisfied and are more likely to stay longer. The property maintains its value and looks well cared for. 

Ignoring repairs can lead to complaints and even legal issues. Regular apartment door repair in Rochester helps maintain a professional image and keeps tenants happy. 

Benefits of Timely Repairs for Tenants 

For tenants, a properly working door improves comfort and security. It also shows responsibility when issues are reported on time. 

A safe and functional door allows you to relax without worrying about security or inconvenience. 

How to Choose the Right Repair Service 

Choosing the right service provider makes a big difference. 

Look for: 

• Experience in door repair 

• Positive customer feedback 

• Fast response time 

• Transparent pricing 

Get Professional Door Repair at Rochester Door Company 

If your apartment door is causing trouble, do not wait for the problem to get worse. A small issue today can turn into a costly repair tomorrow. Taking action now saves time and keeps your space safe. 

At Rochester Door Company, our team delivers trusted apartment door repair in Rochester for both tenants and landlords. We focus on quality work, quick service, and long-lasting results. Contact us today and let our experts restore your door to perfect condition. 

The post Complete Guide to Apartment Door Repair for Tenants and Landlords appeared first on Rochester Door Company.

This guide explains the most common types of commercial doors. Knowing how each one works helps you make a good choice for your specific needs.

Strong Hollow Metal Doors

Hollow metal doors are very common in business settings. They are usually made of steel. Even though the name says “hollow,” the inside is actually filled with insulation or a honeycomb pattern to make it strong.

• Security: These doors are very hard to break. They provide a high level of safety against break-ins.
• Fire Safety: Most metal doors can prevent fire from spreading for a certain period. This is a rule for many business buildings.
• Long-Lasting: Steel does not crack or rot like wood. It stays in good shape even if it gets hit or used a lot every day.

Businesses often use these for back exits, storage rooms, or any area where safety is the primary concern.

Glass and Aluminum Doors for the Front

If you have a retail shop or a restaurant, you probably want people to see inside. Aluminum and glass doors are the standard choice for storefronts.

• Look: These doors look clean and professional. They let in a lot of natural light, which makes a store feel bigger and more welcoming.
• Lightweight: Aluminum is a light metal. This makes the doors easy to open, even for kids or elderly customers.
• Weatherproof: Aluminum does not rust easily. It handles rain and snow well, which is important for buildings in Rochester.

Most of these doors use tempered glass. This is a special type of glass that is much stronger than regular window glass. If it does break, it turns into small dull pieces instead of sharp shards.

Quiet and Classy Commercial Wood Doors

While metal is great for the outside, many businesses use wood doors for the inside. You might see these in offices, schools, or hospitals.

• Sound Control: Wood doors are excellent at blocking noise. This is perfect for meeting rooms or private offices.
• Style: Wood looks warm and high-end. It gives an office space a professional feel.
• Solid Core: This means these doors are heavy and sturdy, unlike the thin doors you might find in homes.

Overhead and Roll-Up Doors for Warehouses

Warehouses, garages, and loading docks need much bigger openings. This is where roll-up or overhead doors come in. Instead of swinging open, they move up toward the ceiling.

• Saves Space: Because they move up, you don’t need to clear a wide path on the floor for the door to swing.
• Easy for Deliveries: These doors are wide enough for trucks to back up to or for forklifts to drive through.
• Manual or Electric: You can get ones that you pull up by hand with a chain, or ones that move with a motor and a button.

Hands-Free Entry with Automatic Sliding Doors

You see these most often at grocery stores and hospitals. They use sensors to open when someone approaches.

• Hands-Free: This is great for people carrying bags or pushing carts. It also helps people with disabilities move around without help.
• Traffic Flow: These doors handle a lot of people moving in and out at the same time very well.
• Energy Savings: Because they close quickly on their own, they help keep the heat or air conditioning from escaping.

Also Read: Front Door Installation Trends for 2026

Why Quality Installation is Important for Your Business

Buying a quality door is only half the job. If the door is installed correctly, it will cause problems later. A slightly crooked door might not lock properly. A door that is too heavy for its hinges will start to sag.

When looking for commercial door installation in Rochester, it is important to find a team that understands the local weather and building rules. A door that works well in a warm climate might not hold up in winter if it isn’t properly sealed.

Ways to Keep Your Doors Working Smoothly

To make your doors last a long time, you should check them a few times a year.

• Check the Hinges: Listen for squeaks. If the door feels heavy or sticks, the hinges might need oil or tightening.
• Look at the Seals: Look for gaps where air is coming in. Replacing a rubber seal is much more affordable than paying a high heating bill.
• Test the Locks: Make sure the key turns easily. If you have to jiggle the key, the lock might be wearing out.
• Clean the Tracks: For sliding or roll-up doors, dirt in the tracks can make the motor work too hard. Keep the tracks clear of trash and rocks.

Choosing the Right Commercial Door for Your Space

To choose the right one, ask yourself these three questions:

1. What is the main use? Is it for customers to enter, or is it for moving big boxes?
2. How much traffic will it get? A door that opens 500 times a day needs to be much stronger than a door that opens five times a day.
3. What is the budget? Metal doors are often more affordable than glass storefronts, but they serve different purposes.

How Rochester Door Company Can Help

At Rochester Door Company, our goal is to help local businesses stay safe and functional. We have years of experience with all kinds of commercial entryways.

Our team can handle everything from small repairs to full replacements. If you have a sticking door, a lock that won’t work, or need a brand-new commercial door installation in Rochester for your building, we are here to help.

The post Complete Guide to Commercial Door Types appeared first on Rochester Door Company.

1. Measuring Tools

Every successful door installation starts with accurate measurements. You’ll need:

• Tape Measure: Essential for measuring the height, width, and thickness of the door and frame.

• Level: Ensures both the frame and door are perfectly straight and balanced.

• Square: Confirms that corners and edges are at correct 90° angles, helping achieve a clean finish.

Without precise measurements, even the best door may not fit properly, causing drafts, squeaks, or alignment issues down the road.

2. Cutting and Shaping Tools

Sometimes old frames need adjustments or slightly uneven floors require trimming. These tools help shape the areas where your new door will go:

• Circular Saw or Hand Saw: Used to trim doors or adjust wooden components to proper size.

• Utility Knife: Handy for cutting insulation, caulk lines, or packaging.

• Chisel: Helps in mortising the space where hinges or latches will sit snugly.

Cut carefully and double-check measurements before making any adjustments — it’s always easier to remove more than to add back material.

3. Fastening Tools

Once everything is measured and trimmed, the next step is securing your door and frame firmly. For this, you’ll need:

• Hammer: Perfect for minor adjustments and securing nails.

• Screwdriver (manual or electric): A must for tightening screws into hinges and frames.

• Drill and Bits: Makes pre-drilling holes and securing screws faster and more precise.

These fastening tools make sure your door stays stable and aligned, even after many years of use.

4. Leveling and Alignment Tools

Alignment matters more than you might think, a slightly crooked door can affect insulation and create gaps. Use:

• Wood Shims: Thin pieces of wood that help position and level the door frame.

• Plumb Bob: A classic but effective tool for checking whether your door is perfectly vertical.

• Laser Level (optional): Offers precision and convenience for larger or more complex installations.

When performing door installation in Rochester, local conditions like humidity or uneven floors can impact alignment, so accurate leveling is crucial for long-term results.

Also Read: Top Benefits of Installing an Access Control System

5. Sealing and Finishing Tools

The final touch makes your door look great and perform well. Proper sealing also protects from drafts and moisture. You’ll need:

• Caulk Gun: For applying sealant around the frame to close gaps.

• Putty Knife: Useful for applying fillers or scraping off old caulk.

• Paintbrush or Roller: Adds the finishing coat of paint or varnish to protect your door and enhance curb appeal.

A well-sealed, well-finished door improves energy efficiency and boosts the value of your home.

6. Safety Equipment

Home projects should always be safe. While door installation is relatively simple, protecting yourself is essential. Keep:

• Safety Glasses: Shield your eyes from sawdust and flying debris.

• Work Gloves: Prevent blisters, splinters, and cuts.

• Ear Protection: Use earplugs when working with power tools.

These small additions make your DIY experience safer and much more comfortable.

7. Optional Power Tools for Faster Work

If you frequently work on home projects, investing in power tools can save you time and effort. Consider these upgrades:

• Cordless Drill/Driver Kit: Quickens assembly and lets you work without cords in the way.

• Jigsaw: Great for detailed cuts or fitting unique door designs.

• Nail Gun: Speeds up fastening when securing trim or molding.

Even though professional installers like Rochester Door Company have all these tools on hand, having your own can make small projects and adjustments a breeze.

Why Choose Rochester Door Company

If gathering all these tools sounds like a big task, don’t worry, Rochester Door Company can handle every detail for you. Their experienced technicians bring advanced tools, the latest installation techniques, and quality doors designed to fit your style and budget.

Whether you’re replacing your front entry or upgrading interior spaces, their experts ensure precise fitting, durable materials, and long-lasting performance. With their trusted door installation in Rochester services, you can rely on skilled professionals who make the process easy, clean, and efficient.

Rochester Door Company is dedicated to helping homeowners create secure, beautiful, and functional entryways, one door at a time.

The post Door Installation Tools Every Homeowner Needs appeared first on Rochester Door Company.

Step 1: Gather the Right Tools and Materials

Before beginning your door installation, it’s important to prepare all the needed supplies. Having everything ready will make the process smoother and prevent unnecessary delays.

You’ll need the following tools and materials:

• Tape measure

• Level

• Hammer or drill

• Screws and nails

• Screwdriver

• Utility knife

• Wood shims

• Caulk and sealant

• Door and hardware (hinges, handles, lockset)

Make sure your tools are in good condition, and keep everything within reach. If you bought your door through Rochester Door Company, you’ll likely receive all the necessary hardware and installation instructions tailored to your specific model.

Step 2: Measure the Door Opening

Accurate measurements are crucial in achieving a snug fit. Measure the width and height of your existing door frame carefully.

Take three width measurements — top, middle, and bottom — and use the smallest one. Then measure the height from the floor to the top of the frame on both sides. Finally, check the frame’s squareness using a level. If you notice unevenness, plan to use shims during installation to adjust the fit.

Remember, minor errors in measurement can lead to major installation issues later on. Double-check your numbers before purchasing your new door.

Step 3: Remove the Old Door and Frame

Start by removing the old door from the hinges. If your frame is damaged or uneven, it’s best to remove it completely to make way for a new pre-hung door unit. Use a utility knife to cut through old caulk and paint where the trim meets the wall, then carefully pry off the molding.

Next, detach the existing frame and threshold (if applicable). Clean up any debris and inspect the surrounding area for rot or water damage before moving on. This ensures a strong, long-lasting foundation for your new door.

Step 4: Prepare the Opening

Once the old frame is out, inspect the rough opening thoroughly. The opening should be level, square, and structurally sound. Use wood shims to correct any uneven surfaces.

Apply waterproof flashing tape along the sill area to help prevent moisture from seeping underneath your door. This small step can make a big difference in keeping your home energy-efficient and protected from water damage year after year.

Step 5: Set the New Door in Place

Now comes the exciting part — installing the new door. Lift the pre-hung door into the rough opening and position it carefully. Make sure the hinge side is perfectly vertical using a level.

Start by temporarily securing the door with a few nails or screws through the hinges. Then, place shims behind each hinge to keep the frame square. Adjust until the door swings freely and closes without rubbing.

It’s common to make slight adjustments during this step. Take your time to ensure a perfect fit before tightening all the screws.

Also Read: How to Choose a Commercial Door Repair Company

Step 6: Secure and Seal the Frame

Once the door is properly aligned, insert screws through the frame into the wall studs. Be sure to screw through the shims for added stability. Double-check that the door still opens and closes smoothly.

After the frame is secured, use insulation foam or caulk to seal any gaps around the edges. Avoid overfilling, as too much foam can expand and distort the frame. When the foam dries, trim the excess and apply the interior and exterior trim molding back in place.

This step improves both the appearance and the energy efficiency of your installation, helping keep drafts and noise out.

Step 7: Attach the Hardware

Now that your door is fully secure, it’s time to install the hardware. Attach the handles, lockset, and any additional accessories your door requires. Follow the manufacturer’s instructions for alignment and function.

Once done, check the latch operation and keyhole alignment. Apply a little lubricant on moving parts to keep them functioning smoothly.

If you’re working with door installation in Rochester professionals like Rochester Door Company, they can also guide you on choosing the best locks and finishes that complement your home’s style and security needs.

Step 8: Paint or Finish the Door

If your new door is unfinished wood, you’ll need to paint, stain, or seal it to protect it from weather damage. Even primed steel or fiberglass doors benefit from a layer of paint for enhanced durability and personal style.

Before painting, clean the surface and apply painter’s tape to protect trim areas. Apply multiple thin coats for an even finish, allowing each coat to dry thoroughly.

Step 9: Final Inspection

Walk around your newly installed door and check everything carefully. Look for smooth operation, even gaps around the edges, and tight seals. Make sure your hardware is properly aligned and secured.

If you notice any small drafts or unevenness, adjust your shims or apply more sealant where needed. Little details like this make the difference between an acceptable job and a professional-grade finish.

Why Choose Rochester Door Company

If you ever feel unsure about tackling door installation in Rochester on your own, don’t worry, Rochester Door Company is here to help. With years of experience and a team of skilled installers, they specialize in helping homeowners achieve beautiful, secure, and energy-efficient door solutions.

Whether you’re replacing a front entry door, upgrading interior doors, or adding custom designs, the company provides top-quality products and professional support throughout the process. From helping you choose the right materials to ensuring precise installation, their goal is to make your project stress-free and long-lasting.

By choosing Rochester Door Company, you’re not just improving your home, you’re investing in reliability, craftsmanship, and lasting value. So, when it’s time for your next door upgrade, reach out to the experts who know doors best.

The post Step-by-Step Door Installation Guide for Homeowners appeared first on Rochester Door Company.

A trusted local company like Rochester Door Company understands how much your business depends on reliable doors. With the right team on your side, you can avoid future headaches and keep your operations running smoothly every day. 

Understand What You Really Need from a Commercial Door Repair Service 

Before you start looking for help, take a moment to understand what your business really needs. Commercial doors come in all types, and each type needs special care. Some common problems include broken hinges, damaged sensors, off-track rollers, or doors that just refuse to close properly. 

If you have a rolling steel door, a glass storefront door, or even a fire-rated door, make sure you choose a commercial door repair company that has experience working with those exact systems. You do not want someone who only works on residential doors. Commercial doors are bigger, heavier, and more complex. The more the company understands your specific door type, the better and faster your repair will be. 

Make a list of the problems you have noticed. Note if the door makes unusual sounds, moves slowly, or feels uneven. This helps the repair company understand your needs right away and gives you a clearer picture when comparing quotes. 

What to Look for When Comparing Commercial Door Repair Companies in Rochester 

When you start looking for a repair company in Rochester, do not rush to hire the first one you find. Take time to compare your options. 

First, check if the company is licensed and insured. This protects both you and your property in case something goes wrong during the repair. A professional company will always have proper documentation ready to show. 

Next, look at experience. Commercial door repair is not something you want to leave to beginners. Ask how long the company has been serving local businesses and what kind of doors they specialize in. 

Response time is another key factor. When your door fails, you cannot afford long waiting hours. Choose a company that offers quick service, especially for emergencies. Many Rochester businesses operate late or early hours, so emergency support can be a big advantage. 

Finally, check if the company offers ongoing maintenance. A repair is great, but regular maintenance can save you from future trouble. 

Checking Reputation and Reviews Before You Commit 

One of the best ways to find a reliable company is to check what other people are saying. Take time to read Google Reviews, Yelp, or other local directories. These reviews tell you what real customers experienced. 

Watch out for signs like no local address or only a few reviews that sound too perfect. That can be a red flag. Good companies have a mix of detailed reviews and visible community presence. 

Also, do not underestimate word of mouth. Ask nearby business owners or property managers in Rochester who they trust for door repair. Local referrals are often more honest and dependable than random online searches. 

When you look through customer feedback, notice how companies respond to complaints. A professional business handles issues politely and works to make things right. For example, Rochester Door Company has built a strong local reputation by focusing on transparent communication and customer satisfaction. You can easily find local reviews from Rochester clients who have worked with our team and trust our services. 

Also Read: How to Choose the Right Door Material for Your Home

Ask These Smart Questions Before Hiring 

Before you sign any agreement, ask some smart questions to make sure you know exactly what you are getting. 

Ask what is included in the service quote. Does it cover both parts and labor? Also, ask if the company offers a warranty on its work. A confident company always stands behind its service. 

Find out what brands or door systems the company is certified to repair. This helps you know if they have the right tools and parts for your specific doors. 

Ask how quickly they can respond in case of emergency calls in Rochester. A good local company understands how important fast service is to business owners. 

Lastly, ask if they provide ongoing maintenance or inspection plans. Regular checks can catch small issues before they turn into big, expensive problems. 

These simple questions can save you time, money, and frustration later. 

Comparing Quotes Without Sacrificing Quality 

When you collect quotes, it is tempting to go with the cheapest option, but cheap is not always better. The lowest price might mean lower quality parts or less experience. Instead of focusing only on price, look at what you get for the money. 

A reliable company gives you a detailed, written estimate that lists everything included in the job. This helps you understand exactly what you are paying for and prevents surprises later. 

Consider things like experience, reputation, and customer service in addition to cost. It is better to pay a little more for a company that will do the job right the first time. 

For example, Rochester Door Company provides clear and honest pricing for all repair and maintenance services. Our team in Rochester believes in transparency so you always know what you are paying for and what to expect. 

Local Expertise Matters: Why a Rochester-Based Company Makes the Difference 

Choosing a local company gives you a big advantage. Local technicians know Rochester’s weather, business environment, and building codes. They can reach you faster, understand common door issues in the area, and provide solutions that actually work for your type of building. 

Working with a local company also builds trust. You know who to call and where to find them. Local businesses often rely on long-term relationships, which means they care more about their reputation and the quality of their service. 

When you choose a Rochester-based team, you get faster response, personal attention, and a stronger sense of accountability. 

Preventative Maintenance: The Secret to Avoiding Future Repairs 

Repairing your door once solves the immediate problem, but regular maintenance keeps those problems from coming back. Preventative maintenance is like a health check for your doors. It helps you catch small issues early and keeps your business running without interruptions. 

During a maintenance visit, technicians check all moving parts, tighten loose hardware, lubricate hinges and rollers, and test safety systems. These small steps can extend the life of your doors and save you from expensive emergency repairs. 

Many Rochester business owners schedule maintenance once or twice a year. It is an easy way to make sure your doors stay strong, safe, and smooth all year long. If you are not sure when to start, talk to a local expert who can inspect your doors and suggest the best maintenance plan for your business. 

Making the Right Choice for Your Business Security and Efficiency 

Choosing the right commercial door repair company in Rochester is all about trust, experience, and local reliability. Look for a team that understands your business needs, responds quickly, and communicates clearly. 

A little research goes a long way in saving time and avoiding future stress. When you pick a company with strong local roots and a history of honest service, you protect your business and your peace of mind. 

If you are looking for a reliable local partner, contact Rochester Door Company today. Our team in Rochester is always ready to help you keep your commercial doors safe, strong, and working like new. 

The post How to Choose a Commercial Door Repair Company appeared first on Rochester Door Company.

That is why more Rochester businesses are moving toward smarter security systems. One of the best upgrades you can make is installing an access control system. It gives you full control over who enters your office and when. 

Our team at Rochester Door Company has helped many local businesses make the switch to secure, modern entry systems that protect their people and property. 

What Is an Access Control System and How Does It Work 

An access control system replaces the need for traditional keys and locks. Instead of carrying a bunch of keys, employees use cards, key fobs, codes, or even their fingerprint to enter the office. You can manage everything from one computer or phone. You can add or remove people anytime you want. 

For example, if an employee leaves your company, you can remove their access instantly. No more worrying about lost keys or old employees still having access. Many Rochester offices are finding this system much easier and safer to manage. 

You can choose from different types of systems such as card readers, mobile apps, or biometric options. Each one can be customized based on how big your office is and how much security you need. 

Improved Office Security and Restricted Access 

One of the biggest benefits is stronger security. With an access control system, you decide exactly who can enter each area of your building. This means sensitive areas like server rooms or supply rooms stay locked unless an authorized person has permission. 

If someone tries to enter without access, the system records it right away. You can check these records anytime. It gives you complete peace of mind knowing your office is always under control. 

Many businesses in Rochester choose our Rochester Door Company access control systems because they know how much safer it makes their workplace. Our systems keep unauthorized visitors out and make your property a lot more secure. 

Enhanced Employee Safety and Peace of Mind 

Your employees deserve to feel safe when they come to work. An access control system helps create that sense of security. Only the people you approve can walk through your doors. This reduces the chance of unwanted visitors or break-ins. 

In case of an emergency, the system allows quick lockdown or alerts so you can protect everyone inside. Employees appreciate knowing their safety matters and that the company takes it seriously. This builds trust and boosts morale. 

In a busy city like Rochester, that added layer of safety can make a big difference for your team’s comfort and focus. 

Simplified Visitor Management and Audit Trails 

Managing visitors can be tricky, especially in offices that receive clients or vendors often. With an access control system, you can create temporary access cards or entry codes for guests. This makes your front desk look more professional and organized. 

You also get a full log of who entered the building, when they came in, and which doors they used. These audit trails are helpful if you ever need to check past activity or meet security compliance standards. 

For industries like healthcare, finance, or technology, these records are not only useful but often required. Businesses in Rochester are realizing how much easier it is to handle visitors with a modern system instead of a paper logbook. 

Also Read: The Benefits of Automatic Sliding Doors for Businesses

Cost Savings and Operational Efficiency 

While installing an access control system requires an initial investment, it quickly pays for itself. You save money because you no longer need to rekey locks every time you lose a key or change staff. You also reduce the risk of theft or damage, which can lower your insurance costs over time. 

Access control systems also help your business run more smoothly. You can set access schedules for after hours or weekends. If certain areas do not need to be open all day, the system can automatically lock them. This saves energy and prevents misuse of spaces. 

For business owners in Rochester who want both security and convenience, this is one of the smartest upgrades to make. 

Integration with Other Office Security Systems 

Access control systems work even better when connected to other security tools. You can link them with your surveillance cameras, alarms, or smart locks. When someone enters the building, your cameras can start recording automatically. 

You can also receive instant notifications on your phone if something unusual happens. Some systems allow you to unlock or lock doors remotely. It gives you more control even when you are not at the office. 

Our team at Rochester Door Company helps local businesses set up complete security solutions that combine access control with other systems. This way, everything works together to give your office full protection. 

How to Choose the Right Access Control System for Your Rochester Office 

Choosing the right system depends on your office size, number of employees, and the level of security you want. Some offices may only need a simple keypad system, while others might need biometric scanners for sensitive areas. 

Before buying, think about how the system will grow with your business. A good access control setup should be easy to expand as your team grows. Also, check that it integrates well with your existing security setup. 

Many business owners in Rochester make the mistake of picking a system that looks good but does not fit their daily needs. That is why it helps to work with local experts like our Rochester Door Company team. We help you choose a system that matches your budget, space, and security goals. 

Make Your Rochester Office Smarter and More Secure

Installing an access control system is one of the best ways to protect your office and improve how it operates. It keeps your people safe, simplifies daily management, and shows that your business values security and organization. 

Whether you run a small office or a large company, you deserve a system that gives you full control. 

If you are ready to make your Rochester office more secure, contact Rochester Door Company today. Our local team can help you design and install the right access control system for your space. Let us help you take the next step toward a smarter, safer, and more efficient workplace right here in Rochester. 

The post Top Benefits of Installing an Access Control System appeared first on Rochester Door Company.

In this in-depth guide, we compare aluminum and wood commercial doors specifically within the context of Rochester’s climate, durability needs, and building standards, so you can make a confident and informed choice for your business.

Rochester’s Harsh Climate and Its Effect on Doors

Rochester experiences all four seasons with intensity—from snowy winters and freezing temperatures to humid summers and occasional heavy rains. These climate conditions affect how materials expand, contract, warp, rust, and decay over time. Therefore, any door material used in a commercial property here must withstand moisture, temperature fluctuations, and abrasive weather conditions.

This is where the debate between aluminum and wood gets particularly interesting. While both can be made to look professional and attractive, they respond very differently to the environment around them.

Aluminum Commercial Doors: Strengths and Weaknesses

Durability and Weather Resistance

Aluminum is inherently resistant to moisture, rust, and corrosion. In a city like Rochester, where winters are harsh and salty slush is common on streets and sidewalks, this is a significant advantage. The metal doesn’t warp or crack due to changing temperatures, making it stable year-round.

Moreover, aluminum doors are often anodized or powder-coated, which adds an extra layer of protection against weather-related wear and tear. These finishes also make them less prone to scratching and fading.

Maintenance Requirements

Aluminum commercial doors require very little maintenance. A simple cleaning with mild detergent and water occasionally is often enough to keep them in good condition. They don’t need repainting, staining, or sealing like wooden doors. This hands-off maintenance is ideal for business owners focused on operations without wanting to worry about frequent upkeep.

Energy Efficiency and Insulation

One area where aluminum slightly lags is thermal performance. On its own, aluminum is a poor insulator. However, modern aluminum doors used in commercial buildings are often thermally broken, meaning they include a plastic section that separates the interior and exterior metal components to reduce heat transfer. This is crucial in Rochester’s cold winters, but it still may not match the insulation provided by solid wood.

Wooden Commercial Doors: Benefits and Drawbacks

Natural Aesthetic and Customization

Wood doors have long been admired for their aesthetic appeal. Their natural grain, warmth, and classic appearance can elevate the look of a commercial entrance, particularly in buildings aiming for a high-end or traditional look. Custom carvings, paneling, and staining give wood an artistic versatility that aluminum typically lacks.

Insulation Properties

Wood is a natural insulator, making it an excellent choice for maintaining indoor temperatures during Rochester’s extreme winters. This quality not only makes commercial spaces more comfortable but can also reduce heating costs over time. Solid wood doors especially provide a dense barrier that limits air infiltration.

Vulnerability to Rochester’s Weather

Despite these strengths, wood has significant vulnerabilities—especially in a city like Rochester. Moisture is wood’s natural enemy. When exposed to snow, rain, or high humidity, untreated or poorly maintained wood can absorb moisture, leading to warping, swelling, and even rot. Over time, this reduces the structural integrity and functionality of the door.

Properly sealed and treated wooden doors can resist these issues for a time, but not indefinitely. The constant cycle of freezing and thawing that occurs in Rochester winters accelerates this degradation unless the wood is meticulously cared for.

Maintenance Demands

Wooden doors demand regular maintenance to remain in good shape. This includes staining or painting every few years, checking for signs of mold, warping, or rot, and resealing when needed. For commercial properties with high foot traffic, this upkeep can become costly and time-consuming.

Lifespan Comparison in Real-World Rochester Conditions

How Long Does Each Material Last?

The lifespan of a commercial door in Rochester, NY, heavily depends on how well it’s maintained and the level of exposure to environmental conditions. Aluminum doors, with minimal upkeep, can last 30 years or more, especially when anodized or coated.

Wooden doors, even when well cared for, generally last 15 to 25 years in exterior commercial settings. That number can drop significantly if exposed to high moisture levels or inconsistent maintenance. Interior wood doors, by contrast, can last much longer due to limited weather exposure.

Commercial Property Use and Foot Traffic

Another aspect to consider is the frequency of use. In high-traffic areas such as schools, hospitals, or office buildings, aluminum tends to be the preferred choice due to its resistance to denting, scratching, and long-term fatigue. Wooden doors may show wear faster in these settings, such as chipped paint or dents.

In boutique storefronts, cafes, or heritage buildings, wood might be chosen for aesthetic value, even if it means a shorter lifespan. But for those prioritizing durability and cost-efficiency, aluminum wins by a clear margin.

Cost Over Time: Value Beyond Purchase Price

Initial Cost vs Long-Term Investment

While aluminum doors may have a higher upfront cost, they generally offer lower total cost of ownership. Fewer repairs, minimal maintenance, and a longer lifespan contribute to their cost-efficiency over time.

Wood doors may be cheaper to install initially, but the required maintenance and risk of damage due to Rochester’s weather mean additional costs will arise. Repainting, replacing water-damaged panels, and addressing insulation issues all add up.

Environmental Considerations

Sustainability is becoming more important for commercial property managers. Wood is a renewable resource, especially when sourced responsibly, and may appeal to those aiming for green building certifications. However, aluminum is recyclable and often made from recycled content, and it lasts longer, which means fewer replacements and less waste over time.

Also Read: Top 5 Signs Your Door Needs Replacement

Choosing What’s Right for Your Business

Matching Door Type to Business Needs

At Rochester Door Company, we often guide clients based on their specific industry, location, and usage level.

Aluminum doors are ideal for:

• High-traffic commercial locations
• Properties exposed to snow, rain, or direct sun
• Business owners seeking long-term value and low maintenance

Wooden doors are better suited for:

• Interior commercial doors or protected exterior entrances
• Upscale businesses where design and aesthetics are top priorities
• Business owners willing to invest in ongoing maintenance

Conclusion

If you’re choosing between aluminum and wood for your commercial property in Rochester, NY, the smart choice for durability and long-term savings is clear: aluminum wins in performance, practicality, and resilience.

At Rochester Door Company, we offer expert guidance, professional installation, and high-quality aluminum and wood commercial doors tailored to your exact needs. Whether you’re outfitting a retail storefront, healthcare facility, or office building, we’ll help you choose the door that lasts—and looks good doing it.

Contact us today to schedule a free consultation and secure your business with the right commercial door for Rochester’s demanding climate.

The post Aluminum vs Wood Doors – Best Choice for Rochester NY appeared first on Rochester Door Company.

If you’ve been looking into options for commercial doors installation in Rochester, this guide is for you. Sliding doors do more than just open and close; they shape the flow of traffic, influence energy efficiency, and can even impact the first impression customers get when they walk into your space.

Let’s break it all down in a way that’s easy to understand and actually useful. 

Why Sliding Doors Make Sense for Businesses

Sliding doors have a clean, modern look. But their appeal is not just about style.

They save space. Unlike swinging doors that need clearance to open, sliding doors move along a track, making them ideal for busy or tight areas. Think about grocery stores, medical clinics, or office lobbies, space efficiency can be a game-changer.

They’re practical. Automatic sliding doors provide easy access for everyone, including people with disabilities or parents with strollers. This isn’t just good business—it’s inclusive design.

They’re energy efficient. Many sliding doors are built with materials that reduce heat loss. Some even come with sensors that open only when needed, helping to keep heating or cooling inside where it belongs.

Steps To Choose The Right Sliding Doors for Your Business

Step 1: Understand Your Business Needs

Before calling anyone for a quote, ask yourself:

• How much traffic comes through your door daily?
• Do you need hands-free operation?
• Is your entrance exposed to extreme weather?
• What level of security do you need?

These answers help shape the door system that’s best for your business. A quiet legal office will have different needs than a busy gas station or shopping mall entrance.

Step 2: Choose the Right Type of Sliding Door

Sliding doors for businesses come in different styles. Let’s cover the most common types:

Automatic Sliding Doors

These are powered by motion sensors. When someone walks up, the door slides open. Perfect for retail stores, airports, and hospitals.

Pros:

• Touch-free
• Smooth flow of traffic
• Very convenient

Cons:

• More expensive than manual options
• Require regular maintenance

Manual Sliding Doors

Best for smaller spaces where automation isn’t necessary. They’re easy to install and maintain.

Pros:

• Lower cost
• Simpler to repair
• Space-saving

Cons:

• Less convenient for people carrying things or with disabilities

Telescoping Sliding Doors

These slide into each other, kind of like layers, to allow a wider opening in a compact space.

Best for:

• High-traffic areas where space is limited

Step 3: Material Matters, Make the Right Choice

Doors come in a range of materials. What you choose affects not only how your door looks but also how it performs.

Glass

Glass sliding doors give a clean, modern appearance and let in natural light.

Best for:

• Retail shops, lobbies, cafes

Watch for:

• Make sure they are tempered or laminated for safety
• Look for Low-E coatings to reduce energy loss

Aluminum

Strong, light, and corrosion-resistant. Aluminum frames work well for glass panels.

Best for:

• Any commercial setting needing a modern look

Bonus: Low maintenance

Steel

If security is a top concern, go with steel. It’s more durable and tougher than other options.

Best for:

• Warehouses, industrial sites, or storage areas

Step 4: Consider Climate and Energy Efficiency

Rochester gets cold in the winter and hot in the summer. That means you’ll need doors that help control indoor temperatures.

Ask your installer about:

• Insulated glass units 
• Weather stripping and airtight seals
• Doors with thermal breaks

Choosing energy-efficient doors not only keeps people comfortable, it lowers your utility bills too.

Step 5: Security Should Never Be an Afterthought

Sliding doors might look sleek, but that doesn’t mean they can’t be strong. You can add:

• Access control systems 
• Security sensors
• Reinforced glass
• Anti-lift devices

If you’re investing in commercial doors installation in Rochester, don’t cut corners on security. It’s easier to add the right systems now than to regret it later.

Step 6: Match Your Brand Style

Believe it or not, your doors say a lot about your business. Are they welcoming? Clean? Professional?

Think about your brand. A trendy coffee shop might go for full-glass doors with dark frames. A legal firm may prefer something more conservative and solid.

You can choose finishes, colors, and hardware that match your logo or interior theme. These details help build trust and consistency in your brand.

Step 7: Don’t Ignore Local Codes and Accessibility Laws

Every city has building codes and accessibility rules, and Rochester is no different.

Make sure your door setup:

• Meets ADA requirements
• Passes local fire and safety codes
• Has proper emergency egress functions

Working with a local company familiar with commercial doors installation in Rochester ensures you’re checking all the boxes without guesswork.

Also Read: Sliding vs. Swinging Doors: Which Door is Best for You?

Step 8: Pick the Right Installer – Why Local Experience Matters

Sliding doors aren’t a DIY job. You need a skilled, certified installer who knows the local climate, codes, and building styles.

Here’s what to look for:

• Local references and positive reviews
• Experience with commercial doors installation in Rochester
• Warranties and after-installation support
• Maintenance and repair plans

Bonus points if they offer 24/7 service in case of emergencies. A malfunctioning door can literally shut your business down for a day or longer.

Step 9: Think Long-Term – Maintenance and Upgrades

Like any machine, sliding doors need care.

Ask your installer about:

• Maintenance schedules 
• Sensor and motor checks
• Cleaning guides for glass and track systems

Some modern systems even allow remote diagnostics or tie into your building’s management system.

If your doors are over 10 years old, it may be time for an upgrade. Technology has improved; today’s sliding doors are quieter, safer, and more energy-efficient than ever.

Looking for a good commercial door installation service in Rochester? Contact Rochester Door Company. Our team has the right tools and experience to install any type of door. Moreover, our experienced professionals will help you choose the best sliding door for your business. 

Contact us today and let’s get started.

The post How to Choose the Right Sliding Doors for Your Business appeared first on Rochester Door Company.